Custom Soldered Copper Roofing & Flashing

Custom soldered copper roofs, bay window and porch roofs, and copper flashing by Jade Roofing & Construction in Martinsburg, WV. Standing seam and flat-lock copper formed to fit and soldered on site, for homes across the Eastern Panhandle, Hagerstown, and Frederick.

Copper Roofing
Home » Our Services » Roofing Services » Copper Roofing

Copper: The Roof That Outlasts the House

Copper roofing is sheet copper formed into standing seam or flat-lock panels and soldered at every joint, so the finished roof is a single watertight skin with no sealant to fail. It goes on for a hundred years or more and turns from bright penny to brown to the green patina you see on church steeples and courthouse domes across the region. It is the most expensive roof we install and the only one your grandchildren will not have to think about.

Most of our copper work is not whole roofs. It is bay window roofs, porch and portico roofs, dormers, cupolas, and the chimney and valley flashing on slate and cedar roofs where anything less than copper would rust out before the roof does. We form the panels and trim ourselves, fit them to the roof, and solder every seam on site with 50/50 solder and a proper flux, the way copper has been laid for two hundred years.

Standing Seam or Flat-Lock

Standing seam copper is for pitched roofs and reads like a fine metal roof with a patina. Flat-lock copper is for low-slope and curved surfaces, laid in small interlocking pans and soldered into one sheet, which is what you see on bay roofs and porch tops. We do both, and we do the ornamental trim, finials, and half-round gutters that go with them.

Soldered, Not Sealed

A copper roof that leaks is almost always one that was screwed and caulked instead of locked and soldered. We do not use exposed fasteners or sealant on copper. Seams are folded, cleated with copper cleats that let the metal expand and contract, and soldered continuously. Expansion is the whole design problem with copper, and we lay out panel lengths and cleat spacing so the roof moves without tearing itself.

Copper also has to be isolated from other metals. We never let it touch galvanized steel, aluminum, or treated lumber, because the runoff will eat them. If you have an existing copper roof or flashing that is leaking, we can usually repair and re-solder it rather than replace it. Jade Roofing & Construction is based in Martinsburg, GAF Certified Plus, a licensed Maryland Home Improvement contractor (MHIC #167279), BBB Accredited, and rated 5.0 across 44 Google reviews. Inspections and written estimates are free.

Why Jade for Copper

Copper is sheet-metal craft, not roofing by the square. Here is what that means with us.

Formed to Fit, Soldered on Site

Panels, pans, and trim formed to your measurements, then locked, cleated, and soldered on the roof. No caulk, no screws.

Built for Movement

Copper expands and contracts more than steel. Cleat spacing and panel lengths are laid out for it, so the seams do not fatigue.

Small Jobs Welcome

Bay roofs, porch tops, cupolas, dormers, and copper flashing for slate and cedar roofs. Most of our copper work is detail work, and we like it.

Common questions about copper roofing

How long does a copper roof last?

Well over 70 years is typical, and 100-plus is common on properly soldered copper. The metal does not rust or degrade; it forms a protective patina. The practical lifespan is set by expansion detailing and by keeping other metals away from it.

The material itself is costly, and the labor is skilled sheet-metal work: forming, locking, cleating, and soldering every seam by hand. You are paying for a roof you will never replace. That is why most homeowners use copper on accents like bay and porch roofs and as flashing rather than across a whole house.

No. New copper is bright, darkens to brown within months, and develops the green patina over years depending on exposure. Some homeowners apply a sealer to slow it; most let it age. We can show you photos of each stage.

Yes, and we recommend it. Copper is the only flashing that will last as long as a slate or cedar roof. We fabricate step, counter, valley, and chimney flashing in copper for our own slate and cedar jobs and for other roofers’ roofs that need it redone.

Usually. Old copper that leaks typically has a cracked solder joint, a split at a fatigue point, or a corroded spot where it touched another metal. We clean, re-solder, or patch with matching copper rather than replacing the whole roof.

Brands We Work With

Jade Roofing & Construction is a GAF Certified Plus contractor, an Owens Corning Platinum Preferred Contractor, and a James Hardie Alliance Select Contractor. We install manufacturer-approved systems from GAF, Owens Corning, CertainTeed, DaVinci Roofscapes, Brava Tile, James Hardie, LP SmartSide, ProVia, Alside, and VELUX.